Your Trusted 24 Hours Service Provider!
  • sns01
  • sns02
  • sns04
  • sns06
  • social (2)
Choosing DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose: Medium, Dimensions and Operating Conditions
  • Your Location:
  • news
  • Choosing DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose: Medium, Dimensions and Operating Conditions

Choosing DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose: Medium, Dimensions and Operating Conditions

HEBEI SINOPULSE TECH GROUP CO.,LTD.JOURNAL / THE BUYER'S GUIDE / SELECTION

THE BUYER'S GUIDE / SELECTION

Choosing DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose: Medium, Dimensions and Operating Conditions

This guide helps procurement teams, distributors, and equipment engineers decide whether the DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose meets their system requirements. It covers the hose's construction, compatible fluid media, available size range (3/16" to 2" ID), working-pressure limits per size, temperature range, and the applications for which it is suited. Where requirements exceed this hose's documented capabilities, alternative options from HEBEI SINOPULSE TECH GROUP CO.,LTD. are noted.

Choosing DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose: Medium, Dimensions and Operating Conditions
Product photo: DIN EN853 1SN/ SAE100R1AT One Steel Wire Braided Hydraulic Hose
01

Compatible fluid medium: The NBR inner tube supports petroleum-based (mineral oil, lubricating oil, diesel, gasoline), synthetic, and water-based (glycol, water-glycol) hydraulic fluids. Fluids outside these categories require separate compatibility verification.

02

Bore size and working pressure: Eleven ID sizes from 3/16" (4.8 mm) to 2" (50.8 mm) are available. Maximum working pressure decreases with bore size, ranging from 25.0 MPa (3,625 PSI) at 3/16" down to 4.0 MPa (580 PSI) at 2". The selected bore must provide a working-pressure rating that exceeds the system peak operating pressure.

03

Operating temperature: Continuous service is rated from −40 °C to +100 °C; intermittent service is rated up to +120 °C. Applications with sustained temperatures above +100 °C require an alternative hose grade.

04

Minimum bend radius: Permissible bend radii range from 90 mm (3/16" bore) to 630 mm (2" bore). Installation routing must not impose tighter bends than the published minimum for the chosen bore size.

05

Standards compliance: The hose meets DIN EN853 1SN, SAE 100R1 type AT (SAE J517 100R1), and ISO 1436 R1AT requirements, with MSHA-accepted cover compound. Buyers whose specifications reference either European (EN) or North American (SAE) designations can use this hose.

What Is the DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose?

The DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose is a single-wire-braid, medium-pressure rubber hydraulic hose manufactured to dual standard compliance: DIN EN853 1SN and SAE 100R1 type AT. It is produced by HEBEI SINOPULSE TECH GROUP CO.,LTD. and is designed for use in hydraulic circuits that convey petroleum-based, synthetic, or water-based hydraulic fluids.

Construction at a glance:

LayerMaterial
Inner tubeOil-resistant synthetic rubber (NBR)
ReinforcementOne braided layer of high-tensile steel wire
Outer coverBlack, abrasion-, ozone-, weather-, and oil-resistant synthetic rubber (MSHA accepted)

The 4:1 safety factor (burst pressure to working pressure) and the single-wire-braid architecture make this hose a practical choice for low- to medium-pressure hydraulic circuits.


Key Selection Criteria

1. Compatible Fluid Medium

The NBR inner tube is compatible with:

  • Petroleum-based hydraulic fluids — mineral oil, lubricating oil, diesel fuel, gasoline
  • Synthetic hydraulic fluids
  • Water-based hydraulic fluids — glycol solutions, water-glycol mixtures

This hose is specifically described as suitable for conveying low- to medium-pressure oil- and water-based hydraulic fluids. If your system uses fluids outside these categories (e.g., phosphate-ester fire-resistant fluids), verify fluid compatibility before selection.

2. Operating Temperature Range

Service typeTemperature range
Continuous service−40 °C to +100 °C (−40 °F to 212 °F)
Intermittent serviceUp to +120 °C (248 °F)

For applications that regularly exceed +100 °C, an alternative hose grade should be evaluated.

3. Dimensions and Working Pressure

The hose is available in eleven standard inside-diameter sizes from 3/16" to 2". Working pressure decreases as bore size increases — a critical factor when specifying the correct size.

Part No.ID (inch)ID (mm)OD (mm)W.P. (MPa)W.P. (PSI)B.P. (MPa)B.P. (PSI)Min. Bend Radius (mm)Weight (kg/m)
1SN-033/16"4.811.525.03,62510014,500900.210
1SN-041/4"6.413.222.53,2639013,0501000.250
1SN-055/16"7.914.721.53,1188512,3251150.311
1SN-063/8"9.517.118.02,6107210,4401300.360
1SN-081/2"12.720.416.02,320649,2801800.451
1SN-105/8"15.923.713.01,885527,5402050.519
1SN-123/4"19.127.310.51,523426,0902400.651
1SN-161"25.436.08.71,262355,0753000.909
1SN-201-1/4"31.842.56.3914253,6544201.300
1SN-241-1/2"38.148.55.0725202,9005001.690
1SN-322"50.862.04.0580162,3206301.891

Selection guidance: Always confirm that your system's peak operating pressure is below the hose's stated working pressure for the selected bore size. Do not exceed published working-pressure values.

4. Applicable Standards

This hose meets the requirements of:

  • SAE 100R1 type AT (SAE J517 100R1) / ISO 1436 R1AT
  • DIN EN853 1SN
  • MSHA accepted cover compound

These dual designations mean the same hose satisfies both European (EN) and North American (SAE) procurement specifications.

5. Bend Radius Constraints

Minimum bend radius values range from 90 mm (3/16" ID) to 630 mm (2" ID). Routing that imposes tighter bends than the published minimum can cause premature hose failure. Check the table above and account for clamp and fitting offsets during installation layout.


Application Fit

The DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose is well suited for the following equipment categories:

  • Agricultural machinery — tractors, harvesters, and implements that use hydraulic systems for lifting, steering, and implement actuation
  • Construction equipment — excavators, loaders, cranes, and similar plant where hydraulic power controls boom and bucket movements
  • Industrial machinery — hydraulic presses, machine tools, and conveying systems
  • Material handling equipment — systems requiring flexible routing in medium-pressure circuits

When This Hose May Not Apply

RequirementRecommended consideration
System pressure exceeds the W.P. for the chosen bore (e.g., above 3,625 PSI at 3/16" or above 580 PSI at 2")Evaluate a two-wire-braid or spiral hose
Continuous temperatures above +100 °CA higher-temperature-rated hose grade should be reviewed
Installation space is very tight and requires a smaller OD than 1SN providesConsider the DIN EN857 1SC compact variant, which has a smaller outside diameter at equivalent working pressures
High-pressure dynamic circuits requiring double-braid reinforcementConsider the DIN EN853 2SN / SAE100R2AT hose, which offers working pressures from 8 to 41.5 MPa

Hose Assembly Options

HEBEI SINOPULSE TECH GROUP CO.,LTD. offers pre-assembled hydraulic hose assemblies with crimp fittings attached. Buyers can specify hose type (1SN), bore size, overall length, and end fittings to receive a finished assembly ready for installation. This reduces on-site fabrication steps and supports consistent crimp quality.


Summary: Selection Checklist

Before ordering the DIN EN853 1SN / SAE100R1AT One Steel Wire Braided Hydraulic Hose, confirm the following:

  1. Fluid compatibility — petroleum, synthetic, or water-based hydraulic fluid ✔
  2. Operating temperature — continuous service below +100 °C (intermittent below +120 °C) ✔
  3. Bore size and working pressure — select the part number whose W.P. exceeds your system peak pressure ✔
  4. Minimum bend radius — routing does not exceed bend-radius limits for the chosen bore ✔
  5. Standard compliance — SAE 100R1AT / DIN EN853 1SN / ISO 1436 R1AT required ✔
  6. Assembly format — bare hose or pre-assembled with crimp fittings ✔

For requirements outside these parameters, contact HEBEI SINOPULSE TECH GROUP CO.,LTD. to identify the appropriate hose specification.

THE COMPANY

HEBEI SINOPULSE TECH GROUP CO.,LTD.

Sinopulse is a renowned company that has been a leading industrial pipe, various hose fittings, and hydraulic hose manufacturer since its establishment in 2011. Founded by three brothers Cao, the company has grown from strength to strength, establishing itself as a key player in the industry.…

About Us ↗Visit company website ↗

YOUR NEXT STEP

Bring your brief. Start a useful conversation.

Use case, specification, quantity and delivery window: make the next conversation specific.

OUR LATEST NEWS
Strict quality control strict production team to ensure stable products quality. Scientific personnel management, efficient production arrangements to ensure our timely delivery.

Product Application

  • Hydraulic Hose Application
  • Industrial Hose Application
  • Silicone Rubber Hose Application
  • Pressure Washing Hose Application
  • industrial hose application -1
  • crimping machine-1
  • Hydraulic hose pressure hose -1
  • gasoline hose -2

If you are interested in our products, you can choose to leave your information here, and we will be in touch with you shortly.